Score Your Deer

TYPICAL
WHITETAIL DEER SCORECHART


INSTRUCTIONS FOR MEASURING TYPICAL WHITETAIL DEER

All measurements must be made with a 1/4-inch wide flexible steel tape to the nearest one-eighth of an inch. (Note: A flexible steel cable can be used to measure points and main beams only.) Enter fractional figures in eighths, without reduction. Official measurements cannot be taken until the antlers have air dried for at least 60 days after the animal was killed.

A. Number of Points on Each Antler: To be counted a point, the projection must be at least one inch long, with the length exceeding width at one inch or more of length. All points are measured from tip of point to nearest edge of beam as illustrated. Beam tip is counted as a point but not measured as a point.

B. Tip to Tip Spread is measured between tips of main beams.

C. Greatest Spread is measured between perpendiculars at a right angle to the center line of the skull at widest part, whether across main beams or points.

D. Inside Spread of Main Beams is measured at a right angle to the center line of the skull at widest point between main beams. Enter this measurement again as the Spread Credit if it is less than or equal to the length of the longer antler; if greater, enter longer antler length for Spread Credit.

E. Total of Lengths of all Abnormal Points: Abnormal Points are those non-typical in location (such as points originating from a point or from bottom or sides of main beam) or extra points beyond the normal pattern of points. Measure in usual manner and enter in appropriate blanks.

F. Length of Main Beam is measured from the center of the lowest outside edge of burr over the outer side to the most distant point of the main beam. The point of beginning is that point on the burr where the center line along the outer side of the beam intersects the burr, then following generally the line of the illustration.

G-1-2-3-4-5-6-7. Length of Normal Points: Normal points project from the top of the main beam. They are measured from nearest edge of main beam over outer curve to tip. Lay the tape along the outer curve of the beam so that the top edge of the tape coincides with the top edge of the beam on both sides of the point to determine the baseline for point measurements. Record point lengths in appropriate blanks.

H-1-2-3-4. Circumferences are taken as detailed in illustration for each measurement. If brow point is missing, take H-1 and H-2 at smallest place between burr and G-2. If G-4 is missing, take H-4 halfway between G-3 and tip of main beam.


 Enter measurement 21 4/8″ as Right
Antler
Left Antler

/
Make sure all measurments are in 8ths, ex. 1/2 = 4/8
A.
Number of Points on Antlers
Spread
Measurements
B.
Tip to Tip Spread

/
C.
Greatest Spread of Main Beams

/

Scoring Measurements
D.
Inside Spread of Main Beams

/
  Right
Antler
Left
Antler
E.
Lengths of Abnormal Points

/

/
 
/

/
 
/

/
 
/

/
 
/

/
      Deductions

Abnormal
PointsTotal:

Right Antler Left Antler
F.
Length of Main Beam

/

/
G1.
Length of First Point

/

/
G2.
Length of Second Point

/

/
G3.
Length of Third Point

/

/
G4.
Length of Fourth Point, If Present

/

/
G5.
Length of Fifth Point, If Present 

/

/
G6.
Length of Sixth Point, If Present

/

/
G7.
Length of Seventh Point, If Present

/

/
H1.
Circumference
at Smallest Place Between Burr and First Point

/

/
H2.
Circumference at Smallest Place Between First and Second Points

/

/
H3.
Circumference at Smallest Place Between Second and Third Points

/

/
H4.
Circumference
at Smallest Place Between Third and Fourth  Points

/

/

Inside
Spread of Main Beams 
If Checked, Spread Limit Applied

Total of all D, E, F, G, & H  Items 

  

Right
Antler Total
F, G, & H
Left
Antler Total
F, G, & H
Total
Deductions
Subtract
Deductions

   

     
Final Score in Fractions 


/